| |
PC90 Pre Clean |
| MATERIAL
SAFETY DATA SHEET |
| |
| |
| THIS
MSDS COMPLIES WITH 29 CFR 1910.1200 ( HAZARD COMMUNICATION STANDARD) |
| IMPORTANT:
Read this MSDS before handling and disposing of this product. |
|
|
|
Pass
this information on to employees, customers, & users of this product. |
|
| |
|
|
|
|
| SECTION
1. CHEMICAL PRODUCTS & COMPANY IDENTIFICATION
/ HAZARD RATINGS |
| PRODUCT
IDENTITY: |
Blend
#9906 PC90 Pre Clean |
HEALTH
RATINGS: |
|
|
| COMPANY
IDENTITY: |
Powers
Paper Company Inc. |
HEALTH
(NFPA) = |
2 |
|
| COMPANY
ADDRESS: |
1000
Armory Place |
HEALTH
(HMIS) = |
2 |
|
| |
Brandenburg,
KY 40108 |
FLAMMABILITY
= |
3 |
|
| COMPANY
PHONE: |
(270)
422-5561 |
REACTIVITY
= |
0 |
|
| |
|
|
SECTION
2. INGREDIENT & REGULATORY INFORMATION
|
| |
All components
of this product are on the TSCA list. |
|
SARA
Title III Section 313 Supplier Notification
|
| |
This
product contains the indicated <*> toxic chemicals subject to the
reporting requirements of Section 313 of the Emergency Planning &
Community Right-To-Know Act of 1986 & of 40 CFR 372. This information
must be included in all MSDSs that are copied and distributed for this
material. |
| |
| SARA
TITLE III INGREDIENTS |
CAS# |
WT. %
|
(REG.SECTION) |
RQ (LBS) |
| |
Light
Aliphatic Solvent Naphtha |
*64742-89-8 |
Not Appl. |
(311,
312) |
None
|
| |
Isopropanol |
67-63-0 |
Not Appl. |
(311,
312) |
None
|
| |
*Mixed
Xylenes |
1330-20-7 |
6 |
(311,
312, 313, RCRA) |
100 |
| |
*Ethylbenzene |
67-56-1 |
<
5 |
(311,
312, 313, RCRA) |
1000
|
| |
| SARA
SECTION 311/312 HAZARDS: Acute Health, Fire |
| MATERIAL |
CAS#
|
TWA
(OSHA)
|
TLV
(ACGIH)
|
HAP
|
| |
Light
Aliphatic Solvent Naphtha |
*64742-89-8 |
500
ppm
|
300 ppm |
No
|
| |
Isopropanol |
67-63-0 |
400 ppm
|
400 ppm
|
No |
| |
*Mixed
Xylenes |
1330-20-7 |
100 ppm
|
100 ppm
|
Yes |
| |
*Ethylbenzene |
67-56-1 |
100 ppm
|
100 ppm
|
Yes |
| |
|
In
addition to EPA Hazardous Air pollutants showing 'Yes' under "HAP" above,
using manufacturers' data, based on EPA Method 311, the following EPA
Hazardous Air Pollutants may be present in trace amounts (less than
0.1%) =
Benzene,
Cumene
|
| |
|
|
|
| MATERIAL |
CAS# |
CEILING |
STEL
(OSHA/ACGIH) |
| |
Light
Aliphatic Solvent Naphtha |
*64742-89-8 |
None
Known |
5.3E3
ppm |
| |
Isopropanol |
67-63-0 |
None
Known |
500 ppm |
| |
*Mixed
Xylenes |
1330-20-7 |
None
Known |
150 ppm |
| |
*Ethylbenzene |
67-56-1 |
None
Known |
125 ppm |
| |
|
THIS
PRODUCT MEETS REQUIREMENTS OF SOUTHERN
|
|
CALIFORNIA
AQMD RULE 443.1 & SIMILAR REGULATIONS
|
|
CALIFORNIA
PROPOSITION 65: This product
contains the following chemicals known to the state of California to
cause cancer & reproductive toxicity: a trace of Benzene
|
| IF >
1472 POUNDS OF THIS PRODUCT IS IN ONE CONTAINER THE
"RQ" IS EXCEEDED. |
| DOT SHIPPING
NAME: Paint Related Material,
3, UN1263, PG II |
| DRUM
LABEL: (FLAMMABLE LIQUID) |
| |
| |
|
SECTION
3. HAZARDS IDENTIFICATION
|
| MATERIAL |
CAS# |
LOWEST
KNOW LETHAL DOSE DATA |
| |
|
|
LOWEST
KNOWN LD50 (ORAL)
|
| |
Xylene |
1330-20-7 |
4000.0
mg/kg (Rats) |
| |
|
|
LOWEST
KNOWN LC50 (VAPORS)
|
| |
Super
VM&P |
*64742-89-8 |
3400.0
mg/kg (Rats) |
| |
| |
|
THRESHOLD
LIMIT VALUE: 260 ppm
(Evaporated Blend)
|
|
CONTAINS:
LIGHT ALIPHATIC SOLVENT NAPHTHA, ISOPROPANOL, MIXED XYLENES,
ETHYLBENZENE
|
|
WARNING!!
|
|
FLAMMABLE!!
|
|
ACUTE
HAZARDS
|
| EYE &
SKIN CONTACT: |
| |
Primary
irritation to skin, defatting, dermatitis. |
| |
Absorption
thru skin increases exposure. |
| |
Primary
irritation to eyes, redness, tearing, blurred vision. |
| |
Liquid
can cause eye irritation. Wash
thoroughly after handling. |
| INHALATION: |
| |
Anesthetic.
Irritates respiratory tract. Acute
overexposure can cause serious nervous system depression. Vapor harmful.
|
| |
Breathing
vapor can cause irritation. |
| |
Acute
overexposure can cause damage to kidneys, blood, nerves, liver & lungs. |
| SWALLOWING: |
| |
Harmful
or fatal if swallowed. |
| |
Swallowing
can cause abdominal irritation, nausea, vomiting & diarrhea. |
| |
|
SUBCHRONIC
HAZARDS / CONDITIONS AGGRAVATED
|
| CONDITIONS
AGGRAVATED |
|
| |
Chronic
overexposure can cause damage to kidneys, blood, nerves, liver, &
lungs. |
|
| |
Persons
with severe skin, liver or kidney problems should avoid use. |
|
|
|
CHRONIC
HAZARDS
|
|
| CANCER,
REPRODUCTIVE & OTHER CHRONIC HAZARDS: |
|
| |
Due
to metabolic differences, the results are not relevant in humans. |
| |
This
product may contain less than 94 ppm of Benzene. |
|
| |
Not considered
hazardous in such low concentrations. |
|
| |
Absorption
through skin may be harmful. Studies
with laboratory animals indicate this product can cause damage to fetus.
|
|
|
|
SECTION
4. FIRST AID MEASURES PROCEDURES
|
| EYE CONTACT: |
| |
For
eyes, flush with plenty of water for 15 minutes & get medical attention. |
| SKIN
CONTACT: |
| |
In
case of contact with skin immediately remove contaminated clothing. |
| |
Wash
thoroughly with soap & water. Wash contaminated clothing before reuse. |
| |
(Discard
contaminated shoes) |
| INHALATION: |
| |
After
high vapor exposure, remove to fresh air.
If breathing is difficult, give oxygen.
If breathing has stopped give |
| |
artificial respiration. CALL A
PHYSICIAN IMMEDIATELY! |
| SWALLOWING: |
| |
If
swallowed, CALL A PHYSICIAN IMMEDIATELY! Do NOT induce vomiting. |
| |
Have
patient lie down & keep warm. Vomiting
may lead to pneumonitis, which may be fatal
|
| |
|
SECTION
5. FIRE FIGHTING MEASURES
|
| AUTO
IGNITION TEMPERATURE: 287 C / 550
F (Lowest Component) |
| LOWER
FLAMMABLE LIMIT IN AIR (% by vol): 1.3 |
| FLASH
POINT (TEST METHOD): 12 C / 54 F (TCC) (Lowest
Component) |
| FLAMMABILITY
CLASSIFICATION: Class I B |
| EXTINGUISHING
MEDIA |
| |
NFPA
Class B extinguishers (Carbon Dioxide or foam) for Class I B liquid fires. |
| SPECIAL
FIRE FIGHTING PROCEDURES |
| |
Water
spray may be ineffective on fire but can protect fire-fighters & cool
closed containers. Use fog nozzles if water is used. |
| |
Do not
enter confined fire-space without full bunker gear. (Helmet with face
shield, bunker coats, gloves & rubber boots). |
| |
Use NIOSH
approved positive-pressure self-contained breathing apparatus. |
| UNUSUAL
EXPLOSION AND FIRE PROCEDURES |
|
FLAMMABLE!!
|
| |
Keep
container tightly closed. |
| |
Isolate
from oxidizers, heat, sparks, electric equipment & open flame. |
| |
Closed
containers may explode if exposed to extreme heat. |
| |
Applying
to hot surfaces requires special precautions. |
| |
Empty
container very hazardous! Continue all label precautions
|
| |
|
SECTION
6. ACCIDENTAL RELEASE MEASURES
|
| SPILL
OR LEAK PROCEDURES |
| |
Stop
spill at source. Dike area & contain. Clean up remainder with absorbent materials.
Mop up & dispose of. Persons without proper protection should
be kept from area until cleaned up. |
| WASTE
DISPOSAL METHOD |
| |
Recycle
or dispose of observing local, state & Federal health, safety &
pollution laws. If questions exist, contact the |
| |
appropriate
agencies. |
| OTHER
PRECAUTIONS |
| |
Vapors
may ignite explosively & spread long distances.
Prevent vapor buildup. Put
out pilot lights & turn off heaters, electric equipment & other
ignition sources during use & until all vapors are gone. |
| |
|
SECTION
7. HANDLING AND STORAGE
|
| HANDLING |
| |
Isolate
from oxidizers, heat, sparks, electric equipment & open flame. |
| |
Use only
with adequate ventilation. Avoid
breathing of vapor or spray mist. |
| |
Avoid
contact with skin & eyes. |
| |
Wear
OSHA Standard goggles or face shield.
Consult Safety Equipment Supplier. |
| |
Wear
gloves, apron & footwear impervious to this material.
Wash clothing before reuse. |
| |
Avoid
free fall of liquid. Ground containers when transferring. Do not flame cut, saw, drill, braze, or weld.
Empty container very hazardous! Continue all label precautions! |
| STORAGE |
| |
Do not
store above 49 C / 120 F. Store
large amounts in structures made for OSHA Class I B liquids. |
| |
Keep
container tightly closed & upright when not in use to prevent leakage. |
| |
|
SECTION
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
|
| EXPOSURE
CONTROLS |
| |
Ventilate
to keep vapors of this material below 130 ppm.
If over TLV, in accordance with 29 CFR 1910.134, use NIOSH approved
positive-pressure self-contained breathing apparatus. Consult Safety Equipment
Supplier. Use explosion-proof
equipment. |
| VENTILATION |
| |
LOCAL
EXHAUST |
= Necessary |
| |
MECHANICAL
(GENERAL) |
= Acceptable |
| |
SPECIAL |
= None |
| |
OTHER |
= None |
| PERSONAL
PROTECTIONS: |
| |
Wear
OSHA Standard goggles or face shield.
Consult Safety Equipment Supplier. |
| |
Wear
gloves, apron & footwear impervious to this material.
Wash clothing before reuse. |
| |
|
|
|
SECTION
9. PHYSICAL DATA
|
| APPEARANCE: |
Liquid,
Water-White |
| ODOR: |
Alcohol |
| BOILING
RANGE: |
83 127 143
C / 182 261 290 F |
| GRAVITY
@ 60 F: |
|
| API: |
52.6 |
| SPECIFIC
GRAVITY (Water = 1): |
.769 |
| POUNDS
/ GALLON: |
6.402 |
| VOC'S
(>0.44 LBS / SQ IN): |
100.1
Vol. % /
769.5 g/L / 6.409
Lbs/Gal |
| TOTAL
VOC'S (TVOC): |
100.0
Vol. % /
768.6 g/L / 6.402
Lbs/Gal |
| NONEXEMPT
VOC'S (CVOC): |
100.0
Vol. % / 768.6 g/L / 6.402 Lbs/Gal |
| HAZARDOUS
AIR POLLUTANTS (HAPS) |
8.5 Wt.
% / 65.3 g/L / .543 Lbs/Gal |
| VAPOR
PRESSURE (mm of Hg) @ 20 C |
15.9 |
| NONEXEMPT
VOC PARTIAL PRESSURE (mm of Hg @ 20 C) |
15.9 |
| VAPOR
DENSITY (air = 1) : |
3.7 |
| WATER
ABSORPTION: |
Moderate |
| SOLVENCY
PARAMETERS: |
|
| HKB (Hydrogen
Bonding) : |
16.8 |
| PKB (Polarity)
: |
34.1 |
| DKB (Dispersion)
: |
49.1 |
| REFRACTIVE
INDEX: |
1.425 |
| MIXED
ANILINE POINT (Acid Insol) |
56 C
/ 133 F |
| |
| |
|
SECTION
10. REACTIVITY DATA
|
| STABILITY |
|
| |
Stable |
| CONDITIONS
TO AVOID |
|
| |
Isolate
from oxidizers, heat, sparks, electric equipment, & open flame. |
| MATERIALS
TO AVOID |
|
| |
Isolate
from strong oxidizers such as permanganates, chromates, & peroxides. |
| HAZARDOUS
DECOMPOSITION PRODUCTS |
|
| |
Carbon
Monoxide, Carbon Dioxide from burning. |
|
| HAZARDOUS
POLYMERIZATION |
|
| |
Will
not occur. |
|
| |
|
|
|
|
| The
supplier disclaims all expressed or implied warranties of merchantability
or fitness for a specific use, with respect to the product or the
information provided herein, except for conformation to contracted
specifications. All information appearing herein is based upon
data obtained from manufacturers and / or recognized technical sources.
While the information is believed to be accurate, we make no
representations as to its accuracy or sufficiency.
Conditions of use are beyond our control, and therefore users
are responsible for verifying the data under their own operating conditions
to determine whether the product is suitable for their particular
purposes and they assume all risks of their use, handling, and disposal
of the product. Users also
assume all risks in regards to the publication or use of, or reliance
upon, information contained herein.
This information relates only to the product designated herein,
and does not related to its use in combination with any other material
or process.
<Back>
|
|
